Exactly How to Install a Bath Tub Yourself: Removing and Replacing.
Exactly How to Install a Bath Tub Yourself: Removing and Replacing.
Blog Article
The publisher is making a few great points relating to How to Install a Bathtub overall in this content down the page.
Mounting a bathtub isn't exactly rocket science, however it does need strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old tub with a new one is likewise a moderately challenging project. If the old bathtub is conveniently easily accessible, the job can relocate rapidly; if you have to open a wall to get rid of the old bathtub and also place the new bathtub, the task is a lot harder. In either instance, the task is within a house handyman's skills, although you will certainly require an assistant to leave the old tub and set in the brand-new one. Make certain you have actually qualified yourself for the job and also fit trying it. Instead of hiring a contractor to take control of a halfway-completed task, it is better to consider employing one before you begin. Chances are you may need an expert plumber to make tube connections.
This short article will assist you install a new bath tub in your washroom if you have actually already purchased a brand-new bathtub as well as don't need to change the setup of your previous water pipes.
Your tools and also product list need to make up the following:
Getting ready for the Installation
Firstly, the sustaining framework supplied with the bathroom must be fitted (if needed) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is very important to ensure that if the faucet includes a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the taps device to prevent pressure on the tub.
Fit the flexible faucet ports to the bottom of the two faucets using 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet through the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you use every one of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom must now prepare to be fitted in its last position.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your setup, after that the first thing you should do is detach the water supply. After doing so, switch on the faucets to drain any type of water continuing to be in the system. The process of eliminating the existing faucets can be quite troublesome as a result of the restricted gain access to that is usually the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the taps. Have a fabric all set for the remaining water that will originate from the pipelines. Once the supply pipes have actually been gotten rid of, use the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the solitary faucets from transforming throughout this procedure. Once the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old sealing substance.
Prior to moving on to fit the new taps, compare the pipe links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Setting up the Tub
Utilizing both wood boards under its feet, position the bath tub in the required position. The wooden boards are valuable in evenly spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 tiny factors.
The following objective is to ensure that the bathtub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the bathtub until the spirit level checks out level.
To install taps, fit the bottom of the furthest flexible tap connector to the appropriate supply pipe by making a compression join; then do the very same for the various other faucet.
Activate the water and also examine all joints as well as brand-new pipework for leaks as well as tighten them if required. Fill the bathtub and also examine the overflow electrical outlet and also the typical outlet for leaks.
Finally, fix the bathroom paneling as defined in the maker's user's manual. Tiling as well as sealing around the bathtub needs to wait till the tub has been used at least when as this will certainly settle it into its last placement.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will need a plastic adapter to avoid damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the other end gives a link to the existing supply pipes.
If you require to fit a monobloc, then you will call for minimizing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the tap in the mounting opening in the bath/basin making sure that the washers remain in place in between the faucet and the sink. Safeguard the faucet in place with the supplier offered backnut. Once the faucet is securely in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular faucet connectors. The previous type needs to be linked to the tap finishes first, tightening up only by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the location where the bath fulfills the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is very important as the installation can move sufficient to break an inflexible seal, triggering the water to pass through the wall in between the bath and also the tiling, resulting in difficulties with dampness and also possible leakages to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your fixtures as well as installations. They are sold in tubes as well as cartridges, and are capable of securing gaps as much as a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of drenched newspaper or soft rope. Remember to constantly fill the tub with water before securing, to permit the motion experienced when the bathtub is in usage. The sealant can split fairly very early if you do not take into consideration this movement before securing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise conveniently available on the market. It is a good idea to fit the floor tiles using water-resistant or water resistant glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I recently found that content on Installing A Bathtub while doing a search on the web. Sharing is good. Helping others is fun. Thanks for taking the time to read it.
Book Services Report this page